|
Copyright © 2001 by BOXLIGHt
Poulsbo, Washington. All rights reserved.
Declaration of Conformity
Manufacturer: BOXLIGHT
19332 Powder Hill Place, Poulsbo, Washington, USA
We declare under our sole responsibility that the XD-10m projector conforms to
the following directives and norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 1992 + A1 + A2 + A3 + A4: 1997
March, 2001
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows are
trademarks or registered trademarks of Microsoft Corporation. Digital Light Pro-
cessing is a trademark or registered trademark of Texas Instruments.
Safety Instructions
Introduction
Image Resolution
Compatibility
Unpacking the Projector
Usage Guidelines
If You Need Assistance
Warranty
1
4
Setting up the Projector
Connecting a Computer
Connecting a Video Player
Turning Off the Projector
Using the Projector
16
19
Basic Image Adjustment
Adjusting the Projector
Using the Remote Control
Using the Keypad and Remote Buttons
Using the On-Screen Menus
Display Menu
Image Menu for Computer Sources
Image Menu for Video Sources
Control Menu
Advanced Menu
Language Menu
Status Menu
Maintenance & Troubleshooting
Cleaning the Lens
Replacing the Projection Lamp
Replacing the Batteries in the Remote Control
Using the Security Lock
27
27
27
31
31
32
Troubleshooting
i
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instruc-
tions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
• Warning: Statements identify conditions or practices that
could result in personal injury.
• Caution:Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention: For information about usage of a feature, please
refer to the User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
Safety Terms:
• Warning: Don’t look directly into the lens when the projector is
turned on.
•Warning: To replace the lamp, turn the projector off
and unplug the power cord. To avoid burns, wait 30 min-
utes before opening the lamp access grill. Follow all instruc-
tions provided in this User’s Guide.
•Warning: Please use the power cord provided.
• Warning: Refer all service to qualified service personnel. Ser-
vicing your own projector will void the warranty. See the fol-
lowing page for the customer service contact information.
• Caution: Don’t block ventilation openings.
iii
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
damage your projector.
• Caution: Don’t place the projector on a hot surface or in direct
sunlight.
• Caution: Do not drop the projector. Transport the projector in a
BOXLIGHT-approved case; see page 37 for a list of cases.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb ruptur-
ing, thoroughly clean the area in front of the projector and dis-
card any edible items placed in that area.
Do not place objects in
this area in front of the projector
Customer Service
If you need assistance, call BOXLIGHT at 1-800-762-5757 or
360-779-7901.
iv
INTRODUCTION
The BOXLIGHT® XD-10m™ digital projector is specifically
designed for the mobile presenter. It generates crisp, clear images
using Digital Light Processing™ (DLP) technology, and features
an M1-DA type DVI connector for easy, built-in digital/analog
and USB connectivity. It is easy to connect, easy to use, easy to
transport, and easy to maintain.
Image Resolution
The XGA resolution of the XD-10m’s projected image is 1024x768.
The projector is compatible with screen resolutions up to
1280x1024. If your computer’s screen resolution is higher than
1280x1024, reset it to a lower resolution before you connect the
projector.
NOTE: The projector automati-
cally expands 640x480 and
800x600 images to 1024x768.
You can display these images at
their native resolutions using the
Resize option in the Image menu.
See page 19 for more information.
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including laptops, up to 1280x1024
resolution.
• Apple® Macintosh® and PowerBook® computers up to
1280x1024 resolution.
• Most standard VCRs, DVD players, HDTV sources, camcord-
ers and laser disc players.
NOTE: The projector is compati-
ble with 1080i and 720P HDTV
formats.
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included. Contact BOXLIGHT immediately if
anything is missing.
If you are experienced in setting up presentation systems, use the
Quick Start card that was included in the shipping box. For com-
plete details on connecting and operating the projector, refer to
this User’s Guide.
1
I
n
t
r
o
d
u
c
t
i
o
n
2
1
3
4
5
t
c
le
e
/s
u
n
e
m
rd
a
rw
fo
ta
a
d
o
e
id
v
k
c
a
e
n
to
s
y
e
k
6
7
8
FIGURE 1
Shipping box contents
1. XD-10m digital projector +
lens cap
5. Remote control
2. Soft carry case
6. Analog computer cable
7. Composite video cable
3. User’s Guide and Quick Start
card
4. Power cord
8. S-video cable
2
focus ring
zoom ring
keypad
computer and video
connectors
power
switch
power
cord
security lock
connector
FIGURE 2
Side view of projector
Usage Guidelines
• Do not look directly into the projection lens when the projector
is turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
• Transport the projector in a BOXLIGHT-approved hard or soft
case.
3
I
n
t
r
o
d
u
c
t
i
o
n
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 32.
If this manual doesn’t answer your question, call BOXLIGHT at
1-800-762-5757 or 360-779-7901.
Warranty
This product is backed by a limited two-year warranty. The
details of the warranty are printed at the back of this manual.
4
SETTING UP THE PROJECTOR
• The projector must be within 10 feet (3 m) of your power
source and within 6 feet (1.8 m) of your computer.
• If you want to project from behind a translucent screen, set
• If the image is too big or too small, use the zoom ring to
adjust the size or move the projector forward or backward.
Figure 3 shows three projected image sizes. For more infor-
mation about image size, see “Projected Image Size” on
page 44.
20 ft./6.1 m
12 ft./3.7 m
5 ft./1.5 m
FIGURE 3
Projected image size at minimum zoom
3 Make sure the projector and the computer are turned off.
5
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
NOTE: Before you continue,
video
computer
make sure the projector and all
other equipment is turned off. If
you’re connecting a computer,
make sure the distance between it
and the projector is 6 feet or less.
power switch
power cord
FIGURE 4
Connector panel
to computer video
to USB mouse
to projector
to computer
FIGURE 5
Computer cable
NOTE: If you are connecting an
older Macintosh computer that
does not have a 15-pin connector,
you must use a Mac adaptor
between the computer and the
projector. See “Optional
Accessories” on page 37.
6
The projector ships with an analog computer cable. If your com-
puter has a digital output, you can order the optional digital com-
puter cable. Using a digital source generates the highest quality
and brightest image possible. See “Optional Accessories” on
page 37.
1 Plug the end of the computer cable with one cable into the
connector on the projector.
2 Plug the blue end of the computer cable into the video connec-
tor on your computer.
NOTE: Many laptop computers
do not automatically turn on their
external video port when a sec-
ondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the exter-
nal video port. Activation com-
mands for some laptop computers
are listed in the Appendix of this
manual on page 38 and in the
Service section of our website.
3 If you want to advance slides in a PowerPoint™ presentation
using the remote, plug the USB cable into the USB mouse con-
nector on your computer.
USB mouse
FIGURE 6
Connecting the projector to a computer
Now you’re ready to power up the projector and your laptop.
Skip to “Powering up the Projector and Adjusting the Image” on
page 9.
NOTE: The USB mouse is sup-
ported for use with Windows 98,
Windows 2000, and Apple OS 8.5
and higher only.
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it
7
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Connecting a Video Player
If your video player uses a round, one-prong composite video
connector, use the composite video cable. If your video player
uses a round, four-prong S-video connector, use the S-video
cable. S-video generates a higher quality image.
1 Plug the composite video cable’s round yellow connector into
the “video-out” connector on your video player (Figure 7).
This connector may be labeled “To Monitor.”
NOTE: HDTV sources must be
connected to the projector using
• If you’re using an S-video cable, connect the round black
connector to the “S-video out” connector on the video
player.
the computer cable (not the video
cable). See the previous pages for
details on connecting this cable.
2 Plug the square yellow connector into the video connector on
the projector.
video cable
FIGURE 7
Connecting the projector to a video player
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, and
SECAM. It automatically adjusts to optimize its performance for
the incoming video.
CAUTION: Your video player
may also have a “Video Out”
connector for a coaxial cable
connection. DO NOT use this to
connect to the projector.
8
Powering up the Projector and Adjusting the Image
1 Remove the lens cap.
NOTE: Always use the power cord
recommended.
that shipped with the projector.
3 Press the Power switch on the back of the projector.
• The fans start to run, the LED on the top of the projector
(Figure 11 on page 14) lights green, and the startup screen
appears. It takes about one minute for the image to achieve
full brightness.
your computer to the projector, the
computer may display a message
stating that new hardware was
found. The Add New Hardware
Wizard may appear. Use the Wiz-
ard to load the correct driver (the
computer considers the projector a
Plug and Play Monitor).
4 If you connected a video player, turn it on.
• The video image should display on the projection screen. If
it doesn’t, press the source button on the keypad (page 14)
or the video button on the remote to display your video
image.
5 Turn on your computer.
screen. If it doesn’t, press the source button on the keypad
or the data button on the remote to display your computer’s
image.
• Make sure your laptop’s external video port is activated;
details.
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
• If necessary, make adjustments to the image using the pro-
jector’s on-screen menus. To open the menus, press the
menu/select button on the keypad or remote. For more
information about the menus, see page 16.
Turning Off the Projector
To turn off the projector, press the Power switch. If you want to
turn the lamp back on, you must allow 90 seconds for the lamp to
cool. The lamp won’t light if it’s too hot.
9
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
10
USING THE PROJECTOR
buttons and the options available from the on-screen menus.
order (page 9).
2 If the image doesn’t display completely, zoom the image
(page 11), adjust the height of the projector (page 12) or center
the image by adjusting its horizontal or vertical position
(page 20). Be sure the projector lens is at a 90 degree angle to
the screen.
4 If the colors don’t look right, adjust the brightness, contrast,
tint, or color (pages 17-18).
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 8) until the image
is clear. To zoom the image, rotate the zoom ring. This adjusts the
image size.
zoom ring
NOTE: To obtain the best overall
focus quality, open the menu and
focus on the text. This will ensure
that the best overall image quality
is achieved.
focus ring
FIGURE 8
Focus ring and zoom ring
11
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
The projector is equipped with a self-locking, quick-release eleva-
tor foot and button.
To raise the projector:
1 Press and hold the elevator button (Figure 9).
2 Raise the projector to the height you want, then release the
button to lock the elevator foot into position.
elevator button
(under finger)
elevator foot
FIGURE 9
Adjusting the height of the projector
12
Using the Remote Control
To use the forward and back buttons on the remote to advance
slides in PowerPoint, you must connect the USB mouse connector
on the computer cable to the computer. See page 7 for details.
Point the remote control at the projection screen or at the front of
the projector (not at the computer). The range for optimum oper-
ation is about 25 feet/7.6m. If you point the remote at the projec-
tion screen, the distance to the screen and back to the projector
must be less than or equal to 25 feet/7.6m. For best results, point
the remote directly at the projector.
enu/select
m
forwar
data
video
back
keystone
FIGURE 10
Remote control
13
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
While the menus are displayed, the source and reset buttons on
the keypad and the up and down arrow buttons on the remote
act as menu navigation and adjustment buttons and the
menu/select button acts as a select button. See “Using the On-
Screen Menus” on page 16 for details.
LED
menu/select
menu/select
forward
source
data
back
video
keystone
reset
FIGURE 11
Keypad and remote buttons
Menu/select
menu/select again (while Exit is highlighted) to close the menus.
(The menus automatically close after 30 seconds if no buttons are
pressed.) When you close the menus, the projector saves any
changes you made. For more information about the on-screen
menus, see page 16.
NOTE: If you have turned Auto
Source off (page 22), you may
need to press the source button
more than once to display an
active source. The sources switch
in this order: data analog, data
digital, S-video, and composite
video.
Source (keypad only)
or Data and Video (remote only)
When you have more than one source (computer and video) con-
nected to the projector, select between them by pressing the
source button on the keypad or the data or video button on the
remote.
14
Reset
(keypad only)
Resets the options in the menus (except Language, Video Stan-
dard, and Rear Projection) to their original settings.
Keystone + - (remote only)
square image.
1 Press the keystone + button to reduce the upper part of the
image, and press the keystone - button to reduce the lower
part. You can also adjust keystone from the Display menu (see
page 17 for details on the menu).
decreasing keystone
increasing keystone
FIGURE 12
Adjusting the keystone
Forward/back buttons (remote only)
These buttons act like the page up and page down buttons on
your computer’s keyboard. You can use them to advance through
cable to your computer. See page 7 for details.
Up/down arrow buttons
Use these buttons to navigate through and make adjustments to
the on-screen menus. See “Using the On-Screen Menus” on
page 16 for details.
15
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the On-Screen Menus
The projector has menus that allow you to make image adjust-
ments and change a variety of settings. These adjustments aren’t
available directly from the keypad.
To open the on-screen menus, press the menu/select button on the
keypad or remote. (The menus automatically close after 30
seconds if no buttons are pressed.) This displays the Main menu
and changes the source and reset buttons on the keypad to menu
NOTE: Some menu items may be
grayed out (dimmed) at certain
times. This indicates the item is
not applicable to your setup or the
item is not enabled until another
selection is made.
navigation buttons. Press the
button to move the cursor
down and press the button to move the cursor up. The
selected menu is highlighted.
FIGURE 13
Main menu
To change a menu setting, use the up and down arrow buttons to
move the cursor up and down to the item you want to change
(the selected item is highlighted), then press menu/select. When
an item is selected, its button appears depressed on-screen. Use
the up and down arrows to adjust the setting or turn it on and off.
Press menu/select when you are done. Press the up and down
arrows to move to another setting. When you have completed
your adjustments, navigate to Exit, then press menu/select. You
are returned to the top of the Main menu. Press menu/select again
to exit the Main menu, or navigate to another submenu.
16
Display Menu
To access the Display menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight Dis-
play, then press menu/select again to access the Display menu.
FIGURE 14
Display menu
Keystone
This option helps to keep the image square as the angle of projec-
tion is changed. Use this feature to adjust the image vertically
and make a squarer image. See page 15 for details on keystone
adjustments.
1 Press the down button to highlight Keystone, then press
menu/select. Use the up and down arrows to adjust the key-
stone setting. Press menu/select to accept your changes.
Brightness
Adjusting the brightness changes the intensity of the image.
1 Use the up and down arrows to highlight Brightness, press
menu/select, use the arrows to adjust the brightness, then
press menu/select to accept your changes.
17
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
1 Use the up and down arrows to highlight Contrast, press
menu/select, use the arrows to adjust the contrast, then press
menu/select to accept your changes.
Tint
The tint adjusts the red-green color balance in the projected
image.
NOTE: The color setting applies
to video sources only. The tint
setting applies to NTSC video
sources only.
1 Use the up and down arrows to highlight Tint, press
menu/select, use the arrows to adjust the tint, then press
menu/select to accept your changes.
Color
The color setting adjusts a video image from black and white to
fully saturated color.
1 Use the up and down arrows to highlight Color, press
menu/select, use the arrows to adjust the color, then press
menu/select to accept your changes.
Blank screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby.
1 Use the up and down arrows to highlight Blank screen, press
menu/select, use the arrows to cycle through the options blue,
black, and white, then press menu/select to accept your selec-
tion.
18
Image Menu for Computer Sources
To access the Image menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight
Image, then press menu/select again to access the Image menu.
FIGURE 15
Image menu for computer sources
Resize
Resize allows you to select from among four different re-sizing
options. The default is Standard, which resizes the image from its
original version to fit a standard 4x3 aspect ratio screen. Wide-
screen Letterbox preserves the 16x9 aspect ratio of the original
theater version, but the image is placed in a 4x3 space, so black
bars appear at the top and bottom of the image. Enhanced Wide-
screen also preserves the aspect ratio of the original theater ver-
sion and is designed to be used with content that is Enhanced for
Widescreen TVs. This option yields more detail than Widescreen
Letterbox. Native reduces the Standard size to match the height of
Enhanced Widescreen.
Highlight Resize, press menu/select, use the up or down arrow
buttons to cycle through the options, then press menu/select to
select.
Auto Image
The projector automatically adjusts tracking, signal synchroniza-
tion and vertical and horizontal position for most computers. If
you want to adjust these features manually, you must turn off
Auto image first.
Highlight Auto image, press menu/select, then press the up or
down arrow buttons to turn this feature off and on.
19
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Manual Sync
The projector adjusts signal synchronization automatically for
most computers. But if the projected computer image looks fuzzy
or streaked, try turning Auto image off then back on again. If the
image still looks bad, try adjusting the signal synchronization
manually:
1 Turn Auto Image off.
2 Highlight Manual sync, press menu/select, use the arrow but-
tons to adjust Manual sync until the image is sharp and free of
streaks, then press menu/select.
Manual Tracking
The projector adjusts tracking automatically to match the video
signal from your computer. However, if the display shows evenly
spaced, fuzzy, vertical lines or if the projected image is too wide
or too narrow for the screen, try turning Auto Image off then back
on again. If the image is still bad, try adjusting the tracking man-
ually:
1 Turn Auto image off.
NOTE: The Manual Sync,
2 Highlight Manual tracking, press menu/select, use the arrow
buttons to adjust Manual tracking until the fuzzy vertical bars
are gone, then press menu/select.
Manual Tracking, Horizontal
Position and Vertical Position
options are available only for
analog computer sources. The
projector sets these options
automatically for digital computer
and video sources, with no manual
override.
Horizontal Position
Follow these steps to manually adjust the horizontal position:
1 Turn Auto image off.
2 Highlight Horizontal position, press menu/select, use the
arrow buttons to adjust the Horizontal position, then press
menu/select.
Positioning adjustments are saved when you turn off the projec-
tor.
Vertical Position
Follow these steps to manually adjust the vertical position.
1 Turn Auto image off.
2 Highlight Vertical position, press menu/select, use the arrow
buttons to adjust the Vertical position, then press menu/select.
Positioning adjustments are saved when you turn off the projec-
tor.
20
Image Menu for Video Sources
FIGURE 16
Image menu for video sources
Resize
Resize allows you to select from among four different re-sizing
options. The default is Standard, which resizes the image from its
original version to fit a standard 4x3 aspect ratio screen. Wide-
screen Letterbox preserves the 16x9 aspect ratio of the original
theater version, but the image is placed in a 4x3 space, so black
bars appear at the top and bottom of the image. Enhanced Wide-
screen also preserves the aspect ratio of the original theater ver-
sion and is designed to be used with content that is Enhanced for
Widescreen TVs. This option yields more detail than Widescreen
Letterbox. Native reduces the Standard size to match the height of
Enhanced Widescreen.
Highlight Resize, press menu/select, use the up or down arrows to
cycle through the options, then press menu/select.
Video Standard (video sources only)
When Video is set to Auto, the projector attempts to pick the
video standard (NTSC, NTSC 4.43, PAL, or SECAM) automati-
cally based on the input signal it receives. (The video standard
options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors might
not look right or the image might appear “torn.” If this happens,
manually select a video standard.
Highlight Video standard, press menu/select, use the up or down
arrows to cycle through the options, then press menu/select to
select.
21
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Control Menu
To access the Control menu settings, press the menu/select button
to display the Main menu, press the down arrow to highlight
Control, then press menu/select again to access the Control menu.
FIGURE 17
Control menu
Auto Source
When this feature is On, the projector automatically finds the
active source, checking the default source first. When this feature
is Off, the projector defaults to the source selected in Default
Source. To display another source, you must manually select one
by pressing the source button on the keypad or the data or video
button on the remote.
Highlight Auto source, press menu/select, then press the up or
down arrow buttons to turn this feature off and on.
Default Source
This determines which source the projector checks first for active
video during power-up. Select among Data-Analog, Data-Digital,
composite video, and S-Video.
Highlight Default source, press menu/select, use the up or down
arrows to cycle through the options, then press menu/select to
select.
22
Advanced Menu
To access the Advanced menu settings, press the menu/select but-
ton to display the Main menu, press the down arrow to highlight
Advanced, then press menu/select again to access the Advanced
menu.
FIGURE 18
Advanced menu
Rear Projection
When you turn Rear Projection on, the projector reverses the
image so you can project from behind a translucent screen.
Highlight Rear Projection, press menu/select, then press the up or
down arrow buttons to turn this feature off and on.
Reset
Highlight Reset then press menu/select to reset the options in the
menus (except Language, Video Standard, and Rear Projection) to
their original settings.
23
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Language Menu
FIGURE 19
Language menu
You can display the on-screen menus in English, French, German,
Spanish, Chinese or Japanese.
1 Press the menu/select button to display the Main menu, press
the arrow buttons to highlight Language, then press
menu/select again to access the Language menu.
2 Press the arrow buttons to highlight the desired language,
then press menu/select. Press menu/select to exit this menu and
return to the Main menu.
24
Status Menu
This is a read-only menu for informational purposes. To display
the Status menu, highlight Status from the Main menu, then press
menu/select.
FIGURE 20
Lamp hours used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in
use. Replace the bulb when the brightness is no longer accept-
able. See “Replacing the Projection Lamp” on page 27 for details.
Computer resolution
Shows your computer’s resolution setting. To change this, go to
your computer’s Control Panel and adjust the resolution in the
Display tab. See your computer’s user’s guide for details.
Source
Indicates the active source, Data-Analog, Data-Digital, Compos-
ite video, or S-video.
Version
Indicates the projector’s software version. This information is
useful when contacting Technical Support.
25
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
26
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•clean the lens
•replace the projection lamp
•replace the batteries in the remote
•use the security lock feature
•troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t
apply the cleaner directly to the lens.
• Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular
motion.
3 If you don’t intend to use the projector immediately, replace
the lens cap.
Replacing the Projection Lamp
The lamp hour counter in the Status menu counts the number of
hours the lamp has been in use. Change the lamp when the
brightness is no longer acceptable. You can order new lamp mod-
ules from BOXLIGHT. See “Accessories” on page 36 for informa-
tion.
WARNING: To avoid burns,
allow the projector to cool for at
least 30 minutes before you open
the lamp access grill. Never
extract the lamp module while the
projector is operating.
Follow these steps to replace the projection lamp:
1 Turn off the projector and unplug the power cord.
2 Wait 30 minutes to allow the projector to cool thoroughly.
27
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
3 Insert a small screwdriver or other flat object into the slot near
the front of the projector. Slide the screwdriver toward the
back of the projector to disengage the lamp access grill, then
slide the lamp access grill off (away from the lens).
WARNING: Be extremely careful
when removing the lamp module.
In the unlikely event that the bulb
ruptures, small glass fragments
may be generated. The lamp
module is designed to contain
these fragments, but use caution
when removing the lamp module.
FIGURE 21
Disengaging and removing the lamp access grill
4 Pull the yellow tab on the lamp module.
CAUTION: Never operate the
projector with the lamp access grill
removed. This disrupts the air flow
and causes the projector to
overheat.
tab
FIGURE 22
Pulling the tab on the lamp module
28
5 Loosen the captive screw on the lamp module.
FIGURE 23
Loosening the screw on the lamp module
6 Grasp the pull tab to pull the lamp module out. Dispose of the
lamp module in an environmentally proper manner.
WARNING: Do not drop the
lamp module or touch the glass
bulb! The glass may shatter and
cause injury.
FIGURE 24
Removing the lamp module
29
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
7 Install the new lamp module.
8 Tighten the screw on the outside of the module.
9 Press the yellow tab to reconnect the lamp module.
10 Replace the lamp access grill by lining up the ribs on the grill
with the marks on the bottom case and sliding the grill in the
direction of the arrows on the bottom case.
11 Plug in the power cord and press the Power switch to turn the
projector back on.
hold the reset button, then press the menu/select button (while
still holding down the reset button) for 10 seconds.
Verify that the counter was reset by pressing the menu/select
button and viewing the counter in the Status menu. See
page 25 for details on the Status menu.
30
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of opera-
tion.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Push the tab on the battery door toward the top of the remote
and lift the door off.
3 Remove the old batteries and dispose of them in an environ-
mentally proper manner.
4 Install two new AAA alkaline batteries. Make sure you install
each in the correct direction.
Using the Security Lock
The projector has a security connector for use with a PC Guardian
Cable Lock System (Figure 25). See “Optional Accessories” on
page 37 for ordering information. Refer to the information that
came with the lock for instructions on how to use it to secure the
projector.
NOTE: The lamp cannot be
removed while the security lock is
attached.
FIGURE 25
Installing the security lock
31
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Troubleshooting
Problem: The projector is not running
•Make sure that the power cord is properly connected to a fully
functional AC electrical outlet. Make sure that the power cord
is also properly connected to the projector.
•If the projector is plugged into a power strip, make sure the
power strip is turned on.
•Make sure the projector is turned on.
Problem: Projector is running, but nothing appears on projec-
tion screen
•Make sure you have removed the lens cap on the projection
lens at the front of the projector.
•Check the projector’s lamp to ensure that it is securely con-
nected in the lamp module. Make sure the lamp access grill is
installed. See “Replacing the Projection Lamp” on page 27.
Problem: Only the start-up screen displays
connection procedures.
•Make sure that the cables do not have any bent pins.
•Verify that the proper input source is connected. See “Source
(keypad only) or Data and Video (remote only)” on page 14.
•You might need to turn everything off and power up the
equipment again in the proper order. Refer to your com-
puter’s documentation to determine the correct order.
•Make sure your laptop’s external video port is turned on. See
the “Portable and Laptop Activation Chart” on page 38 or
your computer’s manual for details.
•Make sure your computer’s video board is installed and con-
figured correctly.
•Make sure your computer has a compatible video board. The
projector isn’t CGA or EGA compatible.
32
If you’re using Windows 98:
1 Open “My Computer” icon, the Control Panel folder and
then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1280x1024 or less.
Problem: Color or text not being projected
•You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 17 for more infor-
mation.
Problem: The screen resolution is not right
no greater than 1280x1024.
Problem: Image isn’t centered on the screen
•Move the projector to reposition the image.
•Reposition the image using the menu. Refer to “Horizontal
Position” on page 20 and “Vertical Position” on page 20.
•Be sure the projector lens is at a 90 degree angle to the screen.
Problem: Image is too wide or narrow for screen
•Adjust the zoom or projector placement.
•Adjust the resolution of your video card if it’s greater than
1280x1024.
Problem: Image is out of focus
•Turn the projection lens to focus the image.
•Make sure the projection screen is at least 5 feet (1.5 m) from
the projector.
Problem: Image and menus are reversed left to right
•Rear projection mode is probably turned on. Turn Rear Projec-
tion off in the Controls menu. The image should immediately
return to forward projection. See “Rear Projection” on
page 23.
33
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
Problem: the projector displays vertical lines, “bleeding” or
spots
•Adjust the brightness. See “Brightness” on page 17.
•Check the projection lens to see if it needs cleaning.
Try these steps in this order.
2 Turn Auto Image off and then back on again. See “Auto
Image” on page 19.
3 Turn Auto Image off and adjust the synchronization and track-
ing manually to find an optimal setting. See “Manual Sync”
on page 20 and “Manual Tracking” on page 20.
•The problem could be with your computer’s video card. If
possible, connect a different computer.
player’s colors
•Just as there are differences in the displays of different moni-
tors, there are often differences between the computer image
and the projected image. Adjust the brightness, tint and/or
Problem: Lamp seems to be getting dimmer
•The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 27.
Problem: Lamp shuts off
•A minor power surge may cause the lamp to shut off. Unplug
the projector, wait at least a minute, then plug it back in.
•Make sure the vents are not blocked.
Before calling BOXLIGHT for assistance, please have the following
information available:
•the projector’s serial number (located on the bottom label)
•the resolution of your computer.
Call BOXLIGHT at 1-800-762-5757 or 360-779-7901
34
APPENDIX
Specifications
The projector must be operated and stored within the tempera-
ture and humidity ranges specified.
Te m p e r a t u re
Operating
50 to 104° F (10 to 40° C) at sea level
50 to 95° F (10 to 35° C) at 10,000 feet
Non-operating
-4 to 158° F (-20 to 70° C)
Altitude
Operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)
Non-operating
Humidity
Operating and non-oper.
10% to 95% relative humidity, non-condensing
Dimensions
6.68 x 8.63 x 2 inches (16.9 x 21.9 x 5.1 cm)
Weight
3.0 lbs. (1.36 kg) unpacked
Optics
Focus Range
4.9 - 16.4 feet (1.5-5 m)
Lamp
Type
120-watt UHP lamp
Input Power Requirements
100-120VAC 2A;50/60Hz
200-240VAC 1A; 50Hz
35
A
p
p
e
n
d
i
x
Accessories
Standard Accessories
(ship with the projector)
Quick Start card
User’s Guide
Soft Case
Shipping Box
Analog Computer Cable 6 ft (1.8 m)
Composite RCA Video Cable 6 ft (1.8 m)
S-video Cable 6 ft (1.8 m)
Remote
Projection Lamp Module (included in projector)
Lens Cap
Power Cords (one ships with projector, type depends on country)
NOTE: Use only BOXLIGHT-
approved accessories. Other
North American Power Cord
Australian Power Cord
UK Power Cord
products have not been tested with
the projector.
European Power Cord
Japanese Power Cord
36
Optional Accessories
Deluxe Travel Case
Hard Travel Porter Case
Projection Lamp Module
Digital Computer Cable
Digital/Analog Interface Card
Macintosh Adaptor
Executive Plus Remote
Full-Feature LaserPro Remote Control
BOXLIGHT GyroMouse Presenter RF Remote (US,
Mexico, Canada, UK only)
Executive Remote IR Receiver
Remote Point RF Remote
PC Guardian Projector Cable Lock
40” Portable Projection Screen
50” Portable Projection Screen
60” Deluxe Insta-Theatre Screen
Portable Projector Stand
37
A
p
p
e
n
d
i
x
Portable and Laptop Activation Chart
Many laptop computers do not automatically turn on their exter-
nal video port when a projector is connected. Activation com-
mands for some laptop computers are listed in the following
table. (If your computer is not listed or the given command does
not work, refer to the computer’s documentation for the appro-
priate command.) On many laptops, the activation function key
is labeled with an icon, for example
or the text CRT/LCD.
NOTE: Usually, pressing the key
commands once activates the
external video port, pressing it
again activates both the external
Key command to
Key command to
de-activate port
Computer
Acer
activate port
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
AST* **
and internal ports, and pressing it
a third time activates the internal
port. Refer to your computer’s
documentation for details on your
specific model.
FN-F5
FN-F5
type from A:/IVGA/CRT
FN-F12
type from A:/IVGA/CRT
FN-F12
AMS
FN-F2
FN-F2
AMT
AT&T
setup screen
setup screen
FN-F3
FN-F6
FN-F3
FN-F6
Advanced Logic
Research
Ctrl-Alt-V
Ctrl-Alt-V
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
setup VGA/
Conf.Simulscan
Conf.Simulscan
Ambra**
FN-F12
FN-F12
FN-F5
FN-F5
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
Amrel* **
Apple
Aspen
Award
BCC*
see Mac Portable and Mac PowerBook
automatic
FN-F6
automatic
FN-F6
automatic
reboot computer
38
Key command to
activate port
Key command to
de-activate port
Computer
Bondwell
LCD or CRT options after
bootup
reboot for LCD or CRT
options to appear
Chaplet**
setup screen
FN-F6
setup screen
FN-F6
FN-F4
FN-F4
Chembook
Commax
FN-F6
FN-F6
Ctrl-Alt-#6
Ctrl-Alt-<
FN-F4
Ctrl-Alt-#5
Ctrl-Alt->
FN-F4
Compaq* **
automatic
mode/? (for setup option)
automatic
automatic
mode/? (for setup option)
automatic
Compuadd* **
Data General
Alt-F for screen setup
option
Alt-F for screen setup
option
Ctrl-Alt-Command
Ctrl-Alt-Command
reboot
Data General
Walkabout
2 CRT/X at DOS prompt
Datavue
DEC**
Ctrl-Shift-M
FN-F5
Ctrl-Shift-M
FN-F5
FN-F4
FN-F4
Dell**
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
FN-F8
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-D
FN-D
FN-F12
FN-F12
Digital*
automatic
reboot
FN-F2
FN-F2
Dolch
Epson
Everex*
For-A
dip switch to CRT
dip switch to CRT
setup screen option
Ctrl-Alt-Shift-C
FN-F10
dip switch to LCD
dip switch to LCD
setup screen option
Ctrl-Shift-Alt-L
Fujitsu
39
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Gateway
FN-F3
FN-F3
FN-F1
FN-F1/FN-F1 again simul-
taneous
Grid* **
FN-F2, choose auto or
simultaneous
FN-F2
Ctrl-Alt-Tab
Ctrl-Alt-Tab
FN-F7
Hitachi
FN-F7
Honeywell
Hyundai
FN-F10
FN-F10
setup screen option
automatic
setup screen option
warm reboot
FN-F2
IBM 970*
IBM ThinkPad**
reboot, enter setup menu
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor plugged
in
unplug monitor
Kris Tech
FN-F8
FN-F8
FN-T
Leading Edge
FN-T
Mac Portable
100
no video port: not compatible
Mac PowerBook
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165, 180,
520, 540, 5300
Control Panel folder, Pow- warm reboot
erBook Display folder;
Activate Video Mirroring
210, 230, 250,
270, 280, 2300
requires Apple Docking Station or Mini Dock
Magitronic
FN-F4
FN-F2
FN-F4
FN-F1
Mastersport
40
Key command to
activate port
Key command to
de-activate port
Computer
Micro Express*
Micron
automatic
warm reboot
FN-F2
FN-F2
Microslate*
Mitsubishi
NCR
automatic
warm reboot
SW2 Off-On-On-On
setup screen option
setup screen option
LCD at the DOS prompt
FN-F3
SW2 On-Off-Off-Off
setup screen option
setup screen option
CRT at the DOS prompt
FN-F3
NEC* **
Olivetti*
automatic
automatic
FN-O/*
FN-O/*
Packard Bell* **
FN-F0
FN-F0
Ctrl-Alt-<
Ctrl-Alt->
Panasonic
Prostar
Samsung*
Sanyo
FN-F2
FN-F2
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to CRT
Ctrl-Shift-M
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to LCD
Ctrl-Shift-M
Sharp
Sun SPARC-
Dataview
Tandy**
Ctrl-Alt-Insert
setup screen option
FN-F5
Ctrl-Alt-Insert
setup screen option
FN-F5
Tangent
Texas Instru-
ments*
setup screen option
setup screen option
Top-Link* **
setup screen option
FN-F6
setup screen option
FN-F6
Toshiba* **
Ctrl-Alt-End
FN-End
Ctrl-Alt-Home
FN-Home
FN-F5
FN-F5
setup screen option
FN-F7
setup screen option
FN-F7
Twinhead*
WinBook
FN-F5
FN-F5
Automatic
Ctrl-Alt-F10
Automatic
Ctrl-Alt-F10
41
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Wyse
software driven
FN-F10
software driven
FN-F10
Zenith**
FN-F2
FN-F2
FN-F1
FN-F1
Zeos**
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
*
These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depend-
ing on the computer model.
42
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer Pow-
erBooks—see below) on, the projector displays the same informa-
tion that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip, then click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as
the primary monitor.
4 Restart the PowerBook.
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and
Sound.
2 In the Resolution list, choose the SimulScan mode, then click
OK.
3 If this changes your display settings, a dialog box appears.
Click OK to confirm the change.
43
A
p
p
e
n
d
i
x
Projected Image Size
NOTE: Use the graph and table
to help you determine projected
image sizes.
250
200
150
100
50
maximum image size
minimum image size
0
5
10
15
20
25
30
Distance to Screen (feet)
FIGURE 26
Projected image size
Table 1:
Range of distance to the screen for a given screen size
Distance to screen
Diagonal
Screen Size
(inches/cm)
Maximum
distance
(feet/m)
Minimum
Distance
(feet/m)
Image Width
(inches/cm)
60/152.4
72/183
48/122
58/147
67/170
72/183
80/203
96/244
120/305
8.5/2.6
10.2/3.1
11.9/3.6
12.7/3.9
14.1/4.3
17.0/5.2
21.2/6.5
6.9/2.1
8.3/2.5
84/213
9.7/3.0
90/229
10.4/3.2
11.6/3.5
13.9/4.2
17.4/5.3
100/254
120/305
150/381
44
cables
INDEX
power 36
A
accessories, ordering 36, 37
activation commands for laptop com-
video 8
centering the image 12, 20
cleaning the projection lens 27
adjusting
brightness 17
color 18
contrast 18
height of the projector 12
keystone 17
don’t match monitor colors 34
compatibility
tint 18
Advanced menu options
Rear projection 23
Reset 23
IBM-compatible 1
Macintosh 1
computer cable 2, 6, 7
altitude limits 35
assistance. See Technical Support
auto image 19
compatible 1
connecting 7
auto source 22
B
power cord 9
brightness, adjusting 17
video player 8
buttons on keypad
Menu/select 14
Reset 15
contrast, adjusting 18
Control menu options
Auto source 22
Default Source 22
Source 14
D
Default Source 22
Display menu options
Blank screen 18
Brightness 17
Color 18
Contrast 18
Keystone 17
Tint 18
displaying on-screen menus 14
45
I
n
d
e
x
E
elevator button/foot 12
keypad 14
keystone adjustment 15
F
focusing the image 11
forward/back buttons 15
fuzzy lines 20
lamp
ordering 36, 37
replacing 27
H
Language menu 24
laptop computers
compatibility 7
HDTV 1, 8, 18
height adjustment 12
I
IBM-compatible computers
compatibility 1
connecting 7
image
connecting 7
adjusting 9, 11
centering 20
colors don’t match computer’s 34
focusing 11
fuzzy lines 20
has lines or spots 34
not centered 33
not displayed 32
out of focus 33
quality 33–34
compatibility 1
connecting 6
resolution 1
menus. See on-screen menus
monitor, projected colors don’t match
34
reversed 23, 33
size 5, 44
streaked 34
too wide or too narrow 33
zooming 11
Auto Image 19
Horiz. Position 20
Manual Sync 20
Manual Tracking 20
Resize 19
on-screen menus
changing language of 24
displaying 16
Vert. Position 20
Video Standard 21
46
P
PAL video 21
power cord
security lock 31, 37
connecting 9
SimulScan, using with PowerBooks 43
Source button 14
ordering 36
power up sequence 9, 32
PowerPoint slides, advancing 15
project from behind the screen 23
projector
specifications 35
Status menu 25
cases 36
S-video, connecting 8
project from behind the screen 23
setting up 5
Technical Support
specifications 35
turning off 9
turning on 9
temperature limits 35
text not visible 33
R
rear projection 23
remote control
advancing PowerPoint slides
replacing the batteries 31
using 13, 14
vertical lines displayed 20, 34
replacing projection lamp module 27
re-positioning the image on the screen
20
video mirroring on a PowerBook 43
video resize 21
Reset button 15
video standard 21
resetting adjustments 15, 23
resetting the lamp hour counter 30
resizing the image 19
resolution 1
W
widescreen video 19, 21
Z
zooming the image 11
47
I
n
d
e
x
48
LIMITED WARRANTY
BOXLIGHT Corporation (“BOXLIGHT”) warrants that each XD-10m (“the Product”) sold hereunder will conform to and func-
tion in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to the first person or
entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said war-
ranty shall continue for a period of two (2) years from the date of such purchase. The standard limited warranty excludes
the lamps in projectors after 120 days and the accessories after one year. BOXLIGHT does not warrant that the Product will
meet the specific requirements of the first person or entity that purchases the Product for personal or business use. BOX-
LIGHT’s liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or
refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replacement Product may be re-furbished in “like-
new” condition, at BOXLIGHT’s sole discretion. To exercise the Purchaser’s rights under the foregoing warranty, the Product
must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any authorized BOXLIGHT service center pro-
vided, and the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of
date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product. When sending your unit in
for repair, please ship your unit in its original packing material or a BOXLIGHT approved ATA Shipping Case, or have a pro-
fessional packaging company pack the unit. Please insure your shipment for its full value. A return authorization number,
issued by the BOXLIGHT customer service department, must also be clearly displayed on the outside of the shipping carton
containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations,
or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or failure to properly use
the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO
YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER
ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF
THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR
LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT’S LIABIL-
ITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT
MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-
AGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
Part Number 010-0270-00
|